Question

How to Install a Custom Rom and its corresponding Kernel (boot.img)

How to Install a android Custom Rom and its corresponding Kernel (boot.img)

Answer 1

How to Install a Custom Rom and its corresponding Kernel (boot.img) 

 

Let the mess .. 

 

Looking for a Rom you like. Make sure it is compatible with your terminal: 

If you have a Hox + international terminal, flash Rom Hox + international one 

If you have a Hox + ATT Telus or terminal, flash Roms Hox + Att / Telus 

Evident. And dangerous to do so as well. 

 

-Connects The USB cable. Go to the phone folders. Create a folder that is called ROMS (not by obligation, but to make it ordenadito) and copy into the Rom you want to install. 

'In the toolkit click Boot into Recovery (you can also do it with the terminal off, pressing the volume-and power buttons for a few seconds, and then going to the recovery menu). If you have not done before, MAKE A BACKUP. 

-Lee This whole sentence before doing anything -> now proceed to Wipear. Tap Wipe and Wipe Cache, Dalvik, Factory Reset, and System. NOTHING. If you do wipe on something else, you will erase the storage including !! ROM you wanted to install, and have the occasional headache to solve the issue (Post 4) 

-Press Install, go to the ROMS folder you created, and selects the one you want to flash. After flashearla, press the back button. Click Reboot and Reboot into Bootloader. Open the Rom you downloaded on the PC, you should see a boot.img file. Leave it somewhere on the pc, and the Toolkit click "Flash a Kernel. Boot.img You select the file you were out there, and will be flashed. 

Reboot from -Press of the phone. To boot the phone normally. 

 

Congratulations !! 

 

As you have seen, and because most terminals have are S-On, you must flasehar rom one hand, and on the other the Kernel. 

Keep in mind that the kernels are not always compatible Roms. You have to read well the characteristics of the roms installed. Many carry their own kernel, or the author will tell if some other kernel that supports Rom.

Answer 2

How to restore the original state 

 

Going back to the original state of the phone. 

There are two ways: 

 

1 Flahsear the orginal RUU (assuming it is available, is the recommended method) 

2 Restore the backup you made ​​in post 1. 

 

Method 1 Flashing the orginal RUU 

 

-Open Toolkit, and click "RUU Factory", that opens the browser with the list of available ruus for Hox +. 

'Do a backup of all data (photos, music, sms .... etc etc) you want to keep. 

-Enchufa The phone to the pc with USB. Click Boot into Bootloader 

Now should I put in the FASTBOOT USB screen 

-Press Relock bootloader. I could give you some security error or say that it has failed. Ignore it, it's normal. 

The phone will boot normally 

When the phone is fully arancado, remove the USB cable and put it back again. Now run the RUU file and follow the instructions. 

The phone will be returned to its original state 

 

 

2.Restaurar backup method. 

 

-Enchufa The phone to the PC. Open the folder of the mobile from the pc to see the files 

-From the PC, go to the folder TWRP-> BACKUPS -> (your serial terminal) -> (folder you want to restore) -> and copy the file to your pc boot.emmc.win. And rename to boot.img This is our kernel to flash 

-boot Into recovery 

-Lee This whole sentence before doing anything -> now proceed to Wipear. Tap Wipe and Wipe Cache, Dalvik, Factory Reset, and System. NOTHING. If you do something else wipe, erase storage, including backup you wanted to install !!, and have the occasional headache to solve the issue (Post 4) 

-Press Back, and then Restore. Eligue you want to restore the Restore 

'Once finished, click back and click Reboot Reboot Bootloader 

-From the Toolkit, flash the kernel to keep above the pc. 

-Restart And have the phone restored to factory settings!

Answer 3

How to flash a Rom by ADB sideload 

 

What is this and what is it? 

Since our device has no SD card, you can be the fact you have cleared all the memory (either done Wipes more, or any other reason) and not have a ROM in the phone memory to flash from recovery . And also not be available the HTC RUU for your phone. 

 

In this case, these are the steps to get back to our terminal ROM: 

 

-boot Manually into recovery. Low volume + power button, hold down until you load the bootloader, select Recovery with the volume keys and power to accept and enter the recovery. 

-Connects USB cable 

TWRP pressed-in "advanced" and then "sideload ADB" 

-Get A ROM, either the Original copy you made, or another. Rename it with a single word, for example CM10.zip QX.zip ARHD.zip ... 

'In the toolkit, in the Extras section, click ADB sideload Rom. Click "yes" when asked if you are in recovery. Select the ROM you want to install. The toolkit will transfer and MT will flash. 

'Once completed, press back. Click Reboot, and bootloader. 

-Extrae The boot.img file from the ROM zip 

-Flashea Kernel boot.img from the toolkit 

Back-and have Rom on the phone !!